0333 003 22 96

Gavita Pro 6/750e DE Flex Complete Fixture for 400V Lamp

From £269.95
You save up to: £170.00
In stock
Grouped product items
Gavita Pro 6/750e DE Flex Complete Fixture for 400V Lamp Code: 3775
Special Price £269.95 Regular Price £439.95
Increase Quantity Decrease Quantity
Gavita Pro 6/750e DE Flex Complete Fixture for 400V Lamp

This is the overview content

Gavita Pro E-Series 6/750 Watt Complete Grow Lights
• Input Voltage:230V-240V (± 10%)
• Input Current 1:3.5A (at 100%)
• Input Power 1:795W (at 100%)
• Input Current 2:3.9A (at 110%)
• Input Power 2:870W (at 110%)
• Power Factor:0,98
• THD:<10%
• Input Frequency:50-60Hz
• Input Connection:IEC C14
• Adjustable:400/500/600/750/825 Watt /EXT
• Certification:CE
• External dim:Gavita Master controller analog protocol (<11,5V)
• External dim connector:RJ14 connector build in (6P4C)
• Article Number: (EU) | (UK) | (CH)
• EAN code:8718403053265 (EU) | 8718403053289 (UK) | 8718403053296 (CH)

Gavita Pro E-Series 6/750 Watt Complete Grow Lights

A) Pro 750e DE / 1000e DE fixture
• Electronic ballast
• Pro-line bracket
• Lever to unlatch reflector
• Lamp sockets
• Reflector Hortistar HR96 750/1000 DE
• Mounting points
B) Three-way control cable splitter (3xRJ14)
C) 2x Interconnect/ drop cable (RJ14/RJ14) - cable length: 1.5 m
D) Gavita Pro 750 W / 1000 W EL 400 V lamp
E) Local power cord

It’s simple to use – everything’s plug and play installation.

Preparing the fixture for use

• Switch off the mains power
• Install the lamp into the fixture (don’t touch it with your bare hands)
• Hang the lamp by its two mounting points)

Connecting the fixture to a Gavita Master Controller

• Use the RJ14 splitters to daisy chain up to 40 fixtures per controller port.
• Set the dials on the fixtures to EXT (External Control)
• Connect the controller to the included RJ14 splitter, using the controller’s connection cable
• Connect one output of the splitter to the RJ14 plug of the fixture by the interconnect cable
• The indicator light on the ballast will blink when the connection is successful
• Connect the other splitter output to the following RJ14 splitter with an interconnect cable
• Repeat this process to connect up to 40 ballasts per controller port

Connecting the fixture to the mains

• Ensure the cord is not coiled and does not touch any hot surfaces.
• Always use a double throw contactor suitable of switching a capacitive load
• Never use household timers to switch the fixture, unless protecting it with a contact!
• If a controller is used, ensure the controller is connected to the fixture.
• Plug the power cord into the mains.
• Switch on mains power.

We recommend using a timer (to automate on/off times), and a contact (to protect your timer).

Changing your lamp & reflector

• It's easy - see the video above!


• Never use the fixture without a lamp or reflector
• Run your lamps at 100% output for at least 100 hours before dimming them to stabilise your lamp
• Always disconnect the fixture from the mains and allow lamps to cool for 30 minutes before performing any maintenance
• Never touch your lamp with bare hands
• Avoid coiled cords
• Ensure the power cord and the controller cable do not touch the reflector
• If external switching gear is used, ensure it can cope with the inrush current of the fixture

    Write Your Own Question

    Search engine powered by ElasticSuite